Child riding a white Biky kids' bike with a closed chain cover and rim brakes outdoors

How to Clean a Kids' Bike and Keep It Running Smoothly

Reviewed: Biky team, November 2026 

To clean a bike your child rides, knock off loose dirt, wash the bike frame and wheels with warm soapy water, rinse with a gentle stream, dry it by hand, and wipe the rims where the rim brakes grip. Then look after the chain the way your child's bike is built: an open chain gets cleaned and lubed, a fully covered chain mostly needs to be left alone, and a balance bike has no chain at all.

Most bike cleaning guides miss that difference because they are written for adult bikes with open chains and gears. On many kids' bikes, including most Biky models, the chain runs inside a closed cover, and scrubbing it like an adult bike's chain is work that does not help.

The short version:

  • Match the clean to the dirt. Dust needs a wipe; mud and wet rides need a wash.

  • Keep the water pressure low. Never use a pressure washer.

  • Keep the rims clean and dry. Brakes on Biky bikes grip the rim, so keep lube and soap off it.

  • Care for the chain by type. Listen first on a covered chain; clean and lube an open one.

Which Clean Does Your Child's Bike Need?

Most kids' bikes do not need a full wash after every ride. Look at the bike first and pick the lightest clean that fixes what you see.

What you see

What to do

Water?

Dust after dry rides

Wipe the frame, handlebar, and seat with a damp cloth; wipe the rims with a dry one

No

Mud, sand, or a ride in the rain

Full wash (5 steps below), then chain care for your model

Yes, low pressure

Road salt or slush

Full wash the same day, with extra attention to the chain area and bolts

Yes, low pressure

Grey streaks on the rims or squeaky brakes

Clean the braking surface (Step 5)

No, rubbing alcohol

Chain sounds dry, scratchy, or rattly

Chain care for your model

Only for an open chain

Bike going into storage

Full wash, dry, chain care

Yes, low pressure

If you are not sure, start with the wipe. It takes minutes and puts no water where it should not go.

What Each Biky Air Needs

Biky makes three kinds of bikes, and their chains need different care. The table uses the specs listed on each product page in November 2026.

Model

Chain

Chain cover

Brakes

What this means for cleaning

Air 12

None

Not needed

Rear Tektro hand brake, or no brake

Wash, dry, wipe the rear rim if it has a brake. Nothing to lube.

Air 14, Air 16, Air 20

KMC Z6, single-speed

Hebie Chainglider (a closed chain cover), front and rear

Front and rear Tektro C310 rim brakes

Wash the outside of the cover; open it only when the chain tells you to.

Air 20 S7, Air 24 S7

KMC Z7, 7-speed

None; open chain with a MicroShift rear derailleur

Front and rear Tektro C310 rim brakes

Clean and lube the chain, rear cogs, and derailleur pulleys after wet or muddy rides.

Biky lists sealed bearings in the hubs and headset of every model, and in the bottom bracket of the pedal models, which is why water pressure matters. And every frame is 6061-T6 aluminum, so mild soap is all the frame needs.

What You Need to Clean a Bike at Home

  • Two ordinary 3- to 5-gallon buckets: one with warm soapy water and one with clean water for rinsing, so you don't put dirt back on the bike with every dip. Park Tool, the bike tool maker, says a quality dish soap is acceptable and that warm water cleans better.

  • Use a soft bike brush or soft sponge for the frame, and an old toothbrush for tight spots. Stiff household scrub brushes can scratch paint; keep a firmer brush for the tires and chain area only.

  • Microfiber cloths: one damp for wiping, one dry for drying, and a rag kept only for the chain.

  • Rubbing alcohol (isopropyl) for the rims.

  • Chain lube and a bike-specific degreaser, only for the S7 models or a covered chain that needs service. Soap lifts mud, but it does little against old, black chain grease; that is the degreaser's job.

No hose or yard? A bucket and a spray bottle are enough for a bike this size. Indoors, put cardboard under it so degreaser and grime do not stain the floor. A repair stand helps but is not required.

How to Clean a Bike in 5 Steps

Step 1: Knock Off Loose Dirt

Let dried mud fall off with a soft brush, or rinse wet mud off gently before you scrub. Rubbing grit into the paint is what scratches it. Remove anything that shouldn't get wet, such as a bell with a battery.

On an S7 with a black, gritty chain, degrease the chain now, before the wash (see Open-Chain Geared Bikes below). Bike mechanics start with the dirtiest parts for a reason: the wash then rinses away the grime and degreaser. On every other bike, there is nothing to degrease.

Step 2: Wash the Bike Frame and Wheels with Warm Soapy Water

Work from the top down: handlebar, seat, bike frame, then the wheels and tires. Use the toothbrush around the bottom bracket (where the cranks meet the frame), behind the fork, and under the seat. On the Air 14, 16, and 20, wash the outside of the Chainglider with the same sponge. It is plastic and cleans like the frame.

Keep a separate brush for the tires and chain area so their grime doesn't end up on the frame or rims.

Step 3: Rinse with Low Water Pressure from the Top Down

Use the clean-water bucket, a watering can, or a garden hose on its softest setting. Park Tool recommends low pressure with a wide spray, never a jet aimed straight at the bearings. Rinse from the top down so dirty water runs off rather than back over clean parts.

Step 4: Dry the Bike by Hand

Dry the whole bike with a towel instead of letting it air-dry. Hand-drying removes leftover soap and gives you a close look at the frame and parts, which is why the same guide recommends it. Water collects around the chain area, bolts, and seat clamp, so dry those last and well.

Step 5: Clean the Braking Surface on the Rims

Every Biky with hand brakes uses rim brakes, which grip the flat sides of the wheel rim. Wipe that strip on both sides of each wheel with a cloth dampened with rubbing alcohol. It lifts the grey mix of road grime and brake pad dust, plus any soap or lube left from the wash, and evaporates quickly.

Finish with three checks: each wheel spins without rubbing, each brake lever feels firm and stops its wheel, and the pads meet the rim without touching the tire. If anything fails, see the shop signs at the end.

Close-up of a black Biky kids' bike with a front rim brake and an adult giving a thumbs-up

Chain Care: Covered vs. Open Chains

A clean chain wears more slowly, and so do the cogs it runs on. How you keep it clean depends on your model.

Bikes with a Chainglider (Air 14, 16, 20): Listen Before You Open

On the Biky Air 14, 16, and 20, a Hebie Chainglider encloses the whole chain, front and rear. It keeps out most of the mud and water that make open chains dirty, so the chain inside doesn't need the routine an adult bike's chain needs. Washing the outside of the cover is enough most of the time.

To decide whether to open it, use what we call the backpedal listen test:

  1. Lift the rear wheel off the ground.

  2. Turn the pedals slowly backward for a few turns, then forward.

  3. Listen and feel.

What you notice

Likely reason

What to do

Quiet, smooth turning

Chain and cover are fine

Nothing

Light rattle on bumpy ground, otherwise smooth

Little lube left inside the cover

Re-lube inside the cover

Scraping, grinding, or stiff pedals

Grit inside, or the cover pressing on the chain

Clean and re-lube inside, check the cover's fit

Treat the backpedal listen test as a rule of thumb built on Hebie's guidance rather than a lab test. Hebie's own advice for a noisy Chainglider is to check chain tension first, then clean and re-lubricate the inside of the cover. Hebie also notes that rattling can happen when the cover runs with little lubricant and that a more viscous lube dampens it (Hebie FAQ).

If the chain needs service inside the cover: how the cover comes off depends on the model, so follow the Biky Air user guide for your bike, or have a bike shop do it at the yearly inspection. When the cover goes back on, Hebie asks for four things:

  • Normal chain lube, and no more of it than the chain would need without a cover.

  • No lube on the snap locks, and every lock fully engaged.

  • A cover that sits loosely on the chain in all directions, with no tension.

  • Clean contact surfaces, with any lube residue wiped off.

Open-Chain Geared Bikes (Air 20 S7, Air 24 S7): Clean, Dry, Apply Chain Lube

The two S7 models run an open KMC Z7 chain through a MicroShift rear derailleur and a 7-speed cassette. Rain and mud reach this chain directly, so it needs care after wet rides and whenever it sounds dry.

  1. Wipe. Hold a rag around the lower part of the chain and pedal backward for several turns. For light dirt, skip to step 4.

  2. Degrease if it is black and gritty. Brush on bike-specific degreaser and let it work for a few minutes, as the label directs, then scrub; or use a clip-on chain scrubber and turn the cranks backward at least thirty times through it, as Park Tool does. Lean the bike so degreaser runs away from the rear hub. Do this before the frame wash (Step 1).

  3. Clean the cogs and pulleys. Brush the rear cogs and the two small wheels on the derailleur, where grime packs in.

  4. Dry. After the wash, run the chain through a dry rag—Lube only a dry chain.

  5. Apply chain lube one drop per link while turning the pedals backward.

  6. Wipe off the excess. Lube left on the outside of the chain collects dirt.

The lube is what protects the chain between washes: it keeps water off the metal and lets the links move freely, so a dry, rusty chain wears out sooner, and so do the rear cogs.

Then shift through all seven gears while turning the pedals to spread the lube. For help with shifting itself, see how to teach a child to shift gears.

Balance Bike (Air 12): No Chain to Lube

The Biky Air 12 has no chain, pedals, or gears. Wash it, dry it, and if it has the rear hand brake, wipe the rear rim with alcohol. Nothing else on it needs attention.

What Not to Use on a Kids' Bike

  • Pressure washers and jet nozzles. Bikes' hubs, headset, and bottom bracket use sealed bearings you don't want to blast.

  • Lube or oily sprays near the rims and pads. On rim brakes, oil on the braking surface reduces grip—Lube the chain with the bike upright and a rag behind the rim, never by spraying.

  • Degreaser anywhere but an open chain and cogs. Keep it off the hubs and brake pads.

  • Gasoline, kerosene, or other flammable solvents. Bike degreaser or soapy water does the job.

  • Abrasive pads or steel wool on paint. A soft brush and mild soap are all the paint needs.

  • Lube on a dirty chain. New lube on top of grit turns into a grinding paste. Clean and dry first.

How Often Should You Clean Your Bike?

There is no fixed schedule for a kids' bike; use the table above. Mileage rules written for adult road bikes do not fit a child who rides to the park twice a week and through puddles on the third day. If your child rides dirt paths or trails often, wash after every muddy ride and wipe in between.

Regular cleaning slows chain and brake pad wear. On an open chain, grit left in place grinds down the chain and cogs, and replacing both costs more than a bottle of lube. A bike that is kept clean is also in better shape to pass down to a younger sibling.

Storing a Kids' Bike for Winter

Put the bike away clean and dry, do the chain care for your model, and keep it indoors if you can. Tires lose some air in storage without a puncture, so before the first spring ride, inflate them to the range on the sidewall and check them as described in how to check tire pressure on a kids' bike. Kids grow over a winter, too: the kids' bike seat height guide shows how to reset the saddle.

When Cleaning Is Not Enough: Signs for a Bike Shop

Washing removes dirt; it does nothing for worn or loose parts. Take the bike to a shop if, after cleaning, you see any of these:

  • Brake pads with no grooves left, or pads that touch the tire, which rim brake pads should never do.

  • A rim that looks dished on the braking surface, or has cracks. Rim brakes slowly wear the rim itself.

  • A covered chain that still scrapes or drags after the listen test and a re-lube. Hebie warns that if dirt builds up enough to add drag, it can damage the cover.

  • An S7 chain that skips gears or has stiff links after cleaning and lubing.

  • Brake levers that pull closer to the handlebar than they used to. Cables stretch over time; see coaster brakes vs. hand brakes for what changes after the first year.

The Biky Air user guides also recommend a shop inspection every 100 miles or at least once a year. Right after winter storage is a good time, and the shop can service the inside of a Chainglider at the same visit.

Jobs Your Child Can Help With

Bike cleaning is an easy way to get a child interested in their own bike. Give them the simple jobs and keep chemicals and adjustments for an adult.

Child can do

Adult does

Wipe the frame, seat, and handlebar with a soapy sponge

Degreasing and lubing the chain

Rinse with a watering can or spray bottle

Alcohol on the rims

Dry the frame with a microfiber cloth

Opening and refitting the Chainglider

Spin the wheels and listen for rubbing

Deciding whether the bike needs a shop

Kids' Bike Cleaning FAQ

Which chain lube should I use on a kids' bike?

Any purpose-made bicycle chain lube works. Wet lube holds up better in rain but picks up more dirt; dry lube stays cleaner but washes off sooner, so you need to reapply it after wet rides. For a Chainglider, Hebie reports good results with a dry film spray and notes that a more viscous lube quiets rattling.

How often should you lube a kids' bike chain?

It depends on the chain. An open chain on an Air 20 S7 or Air 24 S7 needs lube after every wash, after wet rides, and whenever it sounds dry or scratchy. A chain inside a Chainglider on an Air 14, 16, or 20 needs lube only when the backpedal listen test points to it. The Air 12 balance bike has no chain to lube.

Can I clean a kids' bike with household products?

Yes, for most of the job. Dish soap in warm water cleans the frame and wheels, rubbing alcohol cleans the rim braking surface, and an old toothbrush reaches tight spots. The two things worth buying are bicycle chain lube and, for a very dirty open chain, a bike-specific degreaser.

Can I use WD-40 on my child's bike chain?

Not as the chain lube. Park Tool recommends a purpose-made chain lube; a water-displacing spray is a different product.

Do I need to take the wheels off to clean a kids' bike?

No. A kids' bike washes fine with the wheels on. On the Air 14, 16, and 20, the front wheel is bolted on with no quick release, and the chain sits inside its cover, so there is no reason to remove either wheel for cleaning.

My child's chain has orange rust spots. Is it ruined?

Surface rust after a wet spell often cleans off. On an open chain, clean, dry, and lube it, then check that every link bends freely; if links stay stiff, have a shop look at it. On a covered chain, rust is a sign the inside of the cover needs service.


How this guide was checked: Biky specs (chains, chain covers, brakes, bearings, frames) were taken from the Biky Air product pages on November 13, 2026. Washing and chain-care steps were checked against Park Tool repair guides; Chainglider care against Hebie's FAQ. Last reviewed: November 2026.

Sources

Tags:
Older Post Back to Biky Academy Newer Post